Apartment, condo and building-wide Wi-Fi
What is different about building-wide Wi-Fi
Many apartment and condo buildings, campuses, office parks, senior living communities and care homes provide Wi-Fi to every resident from one professional system (Ruckus, Aruba, Cisco Meraki, UniFi and others), run by the property or a service company. These systems are built for hundreds of devices, and they carry settings a home router rarely has. A few of those settings stop small devices like the ticker, while phones, laptops and TVs carry on.
It is not that the ticker is incompatible with professional Wi-Fi: it can join these systems when they are set up for small devices. It is that the building’s settings decide, and only its IT staff can see and change them.
The usual reasons
- Your personal password has a device limit. Many buildings give each resident a password of their own on a shared network name (Ruckus calls this Dynamic PSK). The building can cap how many devices may use one password, lock it to the first devices that used it, or let it expire. A full or locked password can turn the ticker away much as if the password were wrong, while the devices already on it keep working. These passwords are also long and full of symbols, so check every character.
- No usable 2.4 GHz signal where the ticker stands. The ticker hears 2.4 GHz only. TVs, phones and laptops usually use 5 GHz, and building systems often switch some 2.4 GHz radios off or raise the lowest speed they accept, which shortens 2.4 GHz range. The ticker then reports the network as not found, or its signal as weak.
- Protected management frames required, or WPA3 only. The ticker’s chip (an ESP8266 on Espressif’s original software kit) has no protected management frames (PMF, also called 802.11w) and no WPA3. A network set to require either turns it away. Newer TVs and phones have both, so they are not affected.
- Device registration or a sign-in page. Some buildings admit only devices registered by their Wi-Fi address (MAC), or show a page to accept before going online. Devices set up by the building may be registered already; the ticker is not until you register it. See Hotel, cafe and public Wi-Fi for registering it.
- Features that hold new devices back. A minimum-signal threshold (Ruckus’s default is -80 dBm when it is turned on), admission control on a busy access point, or Ruckus’s Transient Client Management, which makes a new device wait 30 seconds by default when it is turned on, can each delay or refuse a join. The ticker gives each join attempt a limited time, then tries again.
- Filters and isolation. These do not stop the ticker joining. A content filter with a “Cryptocurrency” category (Cisco’s and Fortinet’s include one) can block its prices, and a building that keeps each resident’s devices apart can stop your phone reaching its settings page. See Router issues and how to fix them and Guest networks.
What to ask the building’s IT staff
Send them this, or read it to them:
- “My Wi-Fi password: is it limited to a number of devices, or locked to devices that already used it? Can you add one more device, or give me a password for it?”
- “My device works with WPA2 on 2.4 GHz only. Does the network require WPA3, or Protected Management Frames set to Required? Could it be set to Optional or Capable, or is there a 2.4 GHz WPA2 network for smart-home devices?”
- “Is 2.4 GHz on near my unit, and is there a minimum data rate or minimum signal setting?”
- “Do devices have to be registered by MAC address?” (The ticker’s address is the
MACline in its settings page’s footer, read while it is on any Wi-Fi, a phone hotspot will do. TheMAC:in the setup page’s header is a different address.) - “Are fast roaming (802.11r) or Transient Client Management turned on for my network?”
- “Do my phone and this device land on the same private network, so I can reach its settings page?”
Workarounds that do not need the building
- A computer that stays on near the ticker, sharing its internet as a Wi-Fi hotspot: a Wi-Fi of your own, right beside the ticker. See Using a computer as a hotspot.
- A small router of your own, where the building allows it: some units have an Ethernet port in the wall or on the access point. Plug in a small router or travel router, and give it a 2.4 GHz network with WPA2 security. The ticker and your phone join that.
- A phone hotspot, for a test or a short stay: Using a phone hotspot. If the ticker runs on it, the ticker is fine and the building’s settings are the cause.